Glory BC is a completely brush-less truck wash that
will keep the paint looking newer longer. Glory BC
removes virtually any dirt, soil, or stain that is on a
painted surface. Glory BC provides super fast rinsing,
spot free drying, and leaves a brilliant shine. For
polished aluminum, Dazzle BC is recommended.
• Concentrated for super strength with ultimate
• Super fast rinsing
• Spot free Drying
• Safe on paint and glass
• Polished aluminum could be whitened or browned
(use HD Sabre)
• Works equally well in hot or cold temperatures, but
should not exceed 120 Fahrenheit
Appearance: Amber color
Odor: Mild citrus odor
Physical State: Liquid
Boiling Point: >212 F
Specific Gravity (water=1): 1.09 @ 77 F
Evaporation Rate: N/D
Solubility in Water: Complete
Flash Point: N/D
Viscosity Water thin
Decomposition Temp: N/D
Oxidizing Properties: N/D
Protect adjacent surfaces not intended to be cleaned
from exposure to the cleaning solution. Avoid direct
contact with foliage. Avoid wind drift on surrounding
surfaces as well as auto and pedestrian traffic.
Surface & Air Temperatures
Excessively high or low temperatures will produce
poor results and possible harm. Best cleaning results
are obtained when air and surface temperatures are
above 40 Fahrenheit or less than 90Fahrenheit.
Do not clean when temperatures are below freezing
or will be overnight. If freezing conditions exist,
allow adequate time for the surface to thaw. If air
temperatures exceed 90 Fahrenheit, flash cool the
surface with water before applying product. Do not
allow products to dry on the surface. Always rinse
thoroughly while still wet.
Always test prior to beginning full-scale cleaning
operations. Pre-testing will determine suitability
and effectiveness on each type of surface and
stain designated to be cleaned. Pre-testing will also
determine dwell times and number of applications
required to achieve desired results. Pre-testing will
show any potential or adverse reactions to adjacent
surfaces. Allow test areas to thoroughly dry before
evaluating final appearance and results.
Always wear goggles and chemical resistant gloves
when handling this product. Read the Safety Data
Sheet for additional safety and health hazard
information prior to use. Do not get in eyes, on skin,
or on clothing. Do not wear contact lenses when using
this product. If material comes in contact with clothing,
wash before re-use. Do not dilute this product with
any other product except clean water. Do not use
any other application other than specified in the
application instructions. Keep container closed when
not in use. Use with adequate ventilation. Use NIOSH/
MSHA approved respiration devises when adequate
ventilation is not available. Though the potential for
fuming is minimal, take precautions to avoid exposing
building occupants to fumes. Do not remove the label
from the container. Dispose of empty containers in
accordance with federal, state, and local requirements.
First, dilute Glory BC 4 parts water to 1 part Glory BC
to make ready to use then follow the dilution ranges
• 10 parts water to 1 part Glory BC for difficult cleaning
• 20 parts water to 1 part Glory BC for routine
• 50 parts water to 1 part Glory BC for new car
• 3 part water to 1 part Glory BC for whitewalls
Note: Dilutions will vary based on the severity of stain
and type of surface.
1. Pre-wet the surface with water before applying
2. For best brush-less results, apply Glory BC with a
pressure washer – upstream or downstream, or with
a low pressure applicator.
3. Glory BC requires two quick applications, which
leads to complete soil release most of the time. Do
not rinse between applications.
For brush-less results, rinsing requires pressure
washer impact. Proper rinsing techniques determine
the final look and quality of the job. A thorough rinse
job is always recommended; however, our chemistry
never requires flooding the surface. Pressures that
mark the surface should be avoided. When in doubt,
follow the manufacturers recommended P.S.I. for the
substrates. Do not use a zero-degree nozzle.
If Glory BC is used on vehicles that have been washed
with certain silicates, a white film may result. If this
occurs, a solution of HD Sabre, diluted 4 parts water
to 1 part solution is generally effective at remedying
Caution: Do not allow the product to dry on a
Spill or Leak Procedures
Check with state, local, or federal regulation for waste
disposal methods in the area. Wear proper protective
equipment while doing clean-up. For large spills, dike
and contain for intended use. For residual, use a
chemical absorbent material. For small spills, use a
chemical absorbent material and place in an approved
container for disposal.
Store product in a cool, dry place away from alkali-based materials. Vent the bung cap before opening.
Keep container tightly closed when not in use. Wash
thoroughly after handling. For best results, liquid
should be 32 F or higher prior to use.
Instructions in Case of Contact or Exposure
Eyes: Flood with water for 15 minutes. If irritation
develops, seek medical attention.
Skin: Wash off with soap and water. Follow with a
good emollient. If irritation develops, seek medical
Ingestion: Drink lots of water to dilute. Do not induce
vomiting. Seek immediate medical attention.
Inhalation: Move to fresh air. If irritation develops,
seek medical attention.
This product has been classified in accordance with
the hazard criteria of the CFR.
The information herein is given in good faith, but no
warranty, either expressed or implied is made. Final
determination of the suitability of any material is
the sole responsibility of the user. All materials may
present unknown hazards and should be used with
caution. Although certain hazards are described
herein, we cannot be sure or guarantee these are the
only hazards which exist.